|
9.1 An ideal gas flows adiabatically through a duct. At section 1, p1 = 140 kPa, T1 = 260°C, and V1 = 75 m/s. Farther downstream, p2 = 30 kPa and T2 = 207°C. Calculate V2 in m/s and s2 ? s1 in J/(kg ? K) if the gas is (a) air, k = 1.4, and (b) argon, k = 1.67.
Fig. P9.1
Solution: (a) For
|
|
|
5.1 For axial flow through a circular tube, the Reynolds number for transition to turbulence is approximately 2300 [see Eq. (6.2)], based upon the diameter and average velocity. If d = 5 cm and the fluid is kerosene at 20°C, find the volume flow rate in m3/h which causes transition.
Solution: For
|
|
|
Solution: For water, take ρ = 998 kg/m3 and ? = 0.001 kg/m-s. The surface wave speed is co = gy = (9.81 m/s2)(0.1 m) = 0.99m/s
The average velocity is determined from the given flow rate and area:
V = Q A = (80,000 cm3 /s) (30 cm)(10 cm) = 267 cm s = 2.67 m s Froude number: Fr = V co = 2
|
|
|
Solution: Make a plot of density ρ versus altitude z in the atmosphere, from Table A.6:
1.2255 kg/m3
ρ
0 z 30,000 m
This writer’s approximation: The curve is approximately an exponential, ρ ? ρ o exp(-b z), with b approximately equal to 0.00011 pe
|
|
|
Solution: The area element for this axisymmetric flow is dA = 2 π r dr. From Eq. (3.7),
Q= u dA= C 0 R ∫ (R2 ?r2)2 π rdr=
π 2CR4 Ans.∫
2
P3.4 A fire hose has a 12.5-cm inside diameter and is flowing at 2.27 m3/min. The flow exits through a nozzle contraction at a d
|
|
|
P7.1 An ideal gas, at 20°C and 1 atm, flows at 12 m/s past a thin flat plate. At a position 60 cm downstream of the leading edge, the boundary layer thickness is 5 mm. Which of the 13 gases in Table A.4 is this likely to be?
Solution: We are looking for the kinematic viscosity. For a gas at l
|
|
|
P6.1 An engineer claims that flow of SAE 30W oil, at 20°C, through a 5-cm-diameter smooth pipe at 1 million N/h, is laminar. Do you agree? A million newtons is a lot, so this sounds like an awfully high flow rate. Solution: For SAE 30W oil at 20°C (Table A.3), take ρ = 891 kg/m3 and ? = 0.29 kg/m
|
|
|
fluid, but there is always a limiting very-high viscosity for which performance will deteriorate. Can you explain the probable reason? Solution: High-viscosity fluids take a long time to enter and fill the inlet cavity of a PDP. Thus a PDP pumping high-viscosity liquid should be run slowly to ensure
|
|
|
P4.1 An idealized velocity field is given by the formula
Is this flow field steady or unsteady? Is it two- or three-dimensional? At the point (x, y, z) = (?1, +1, 0), compute (a) the acceleration vector and (b) any unit vector normal to the acceleration. Solution: (a) The flow is unsteady beca
|
|
|
2.1 For the two-dimensional stress field in Fig. P2.1, let σ xx =150 kPa σ yy =100 kPa σ xy =25 kPa Find the shear and normal stresses on plane AA cutting through at 30°. Solution: Make cut “AA” so that it just hits the bottom right corner of the element. This gives the freebody shown at right. Now
|
|
메뉴펼치기
